We've stumbled upon this post involving A Step-by-Step Guide to Installing a Bathtub directly below on the net and think it made perfect sense to relate it with you over here.
Installing a tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily available, the job can move immediately; if you need to open up a wall surface to eliminate the old bathtub as well as position the new tub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will need a helper to move out the old tub and also embeded in the brand-new one. See to it you have actually certified yourself for the task and are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed project, it is better to take into consideration utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually already purchased a brand-new bathtub and do not need to change the setup of your previous water system pipes.
Your devices as well as product list should consist of the following:
- New Tub
- Hammer
- Pipe Wrenches
- Prybar
- Shatterproof glass
- Level
- Pliers
- Flexible Wrench
- Putty Knife
- Screwdriver
- Cold Chisel
- Measuring tape
- Pipe Caps
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be rather problematic because of the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Secure the tap in position with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former type must be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bathtub until the spirit level reads level.
To install faucets, fit all-time low of the outermost adaptable faucet port to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the water system as well as inspect all joints and new pipework for leakages and also tighten them if needed. Load the bath tub as well as likewise check the overflow outlet as well as the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling as well as securing around the tub ought to wait until the bathtub has actually been made use of at the very least once as this will settle it right into its last setting.
Getting ready for the Installation
Firstly, the sustaining structure provided with the bath ought to be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent pressure on the bath tub.
Fit the versatile tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split a rigid seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealant can break rather very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is recommended to fit the floor tiles making use of water-resistant or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about How to Install a Bathtub Yourself? Place a remark down below. We will be interested to see your reactions about this write up. We hope to see you back again in the near future. Be sure to set aside a second to share this page if you enjoyed reading it. I truly appreciate reading our article about How to Install a Bathtub.
Request Your Service
Comments on “Just How to Replace a Bathtub”